Drawer Box Depth 24 Cabinets
How to Measure for Replacement Kitchen Drawer Boxes
Kitchen drawers suffer a lot of wear and tear. Over the years they get yanked open and slammed shut thousands of times, and heavy contents shift with every movement causing the sides and lesser to loosen and eventually fail. If your kitchen came equipped with drawer boxes synthetic using dovetail joinery, so they are probably still in peachy shape. But, if your kitchen has the typical builder grade drawer boxes held together with staples, they probable need replacement.
An ideal time to supplant onetime, worn out or broken drawer boxes is during a cabinet refacing project. Replacing your chiffonier doors is an ideal mode to beautify your kitchen and add value, replacing drawer boxes will increase the utility of your kitchen in just a few easy steps. You can even convert a doored cabinet to a pot and pan stack for added functionality.
How to Measure for Custom Dovetail Drawers:
ane . Remove Drawer Box to Measure
Carefully remove your existing drawer boxes from the chiffonier frame in lodge to accurately measure. Empty the contents of your drawers before removing equally the drawers can be quite heavy when loaded.
two . Mensurate the Within Cabinet Width (ICW)
Two factors will determine the width of your new drawer box: the Inside Cabinet Width of the cabinet that volition house the drawers, and the type of drawer slide being used. The type of drawer slide being used will decide how much width is deducted from the drawer box in club accommodate the slide. For loftier quality soft shut undermount slides like Blum (the preferred choice for most homeowners), the deduction is only iii/eight". A side mounted slide, which can be more economical, requires a deduction in width of ane", making for a smaller drawer box.
The ICW is adamant by simply measuring the cabinet opening. On a framed kitchen this will be the inside measurement of the face frame from left to right.
On a frameless kitchen, the ICW is the inside width of the cabinet box itself.
3.Measure the Height of Your Drawer Box
Side by side comes measuring the height of your drawer box. Measure out the peak of the exterior of the drawer box you are replacing. Nearly drawer manufacturers have standard heights ranging from two.25" to ten.25" which cover the virtually mutual drawer box heights used in cabinetry over the terminal several decades.
Altering the height of your drawer box is doable, for instance if you lot desire to replace ii shallow drawer boxes with a unmarried deeper drawer box for pots and pans. Just remember to adapt the height of your drawer face up to adjust the drawer box. In general, the height of the drawer face should be 1.75" to ii" higher than the drawer box in order to suit the undermount slides and overlay.
4.Measure the Depth
Mensurate the depth of the cabinet from the back of the cabinet box to the front. Virtually base of operations cabinets are 24" deep. When measuring, check for obstructions in the dorsum of the cabinets. In some cases, builders may run electric or plumbing through the back of cabinets and you may need to deduct from the depth to clear the obstructions. The standard drawer depth for a 24" base cabinet is approximately 21". A quality drawer glide like the Blum Tandem Undermount slide will let for total extension of the drawer box for easier access. In general, the drawer box depth yous select volition exist 2-iii inches less than the depth of the cabinet.
5. Ordering New Drawer Boxes
With the measurements you took using the steps higher up y'all are at present ready to gild your custom dovetail drawer boxes using our online order course.
Select "Width Blazon" as Inside Cabinet Width and then enter your ICW width in the next box. Select the Height of the drawer box required using the drop-downwards menu. Finally, select Depth using the drop-down carte du jour. Selecting the Blum Undermount Slide will ensure your drawer boxes arrive ready to install. We volition fifty-fifty mount the Blum locking device to the underside of the drawer box for you.
Notation – if yous are replacing drawer boxes but intend to supply your own slides please select Exact Drawer Dimension under width type and input your drawer box width. Your measurements should be the verbal size of the drawer box required (closest to our standard Meridian and Depth) .
Dovetail Drawer Box Features:
Custom dovetail drawers from Nieu include:
- 5/8" thick solid birch construction
- Dovetail joinery built for a lifetime of durability
- Low VOC, articulate UV end for actress water resistance
- 3/8" matched melamine bottom for added load capacity
- Shipped get together for easy installation
- Blum locking devices installed for you when Blum slides added to your drawer order
Source: https://www.nieucabinetdoors.com/how-to-measure-for-replacement-drawer-boxes/#:~:text=The%20standard%20drawer%20depth%20for,base%20cabinet%20is%20approximately%2021%E2%80%9D.